OTC (9330) Stinger 30 Ton Bottle Jack #ad - Forged base and cylinder to ensure strength and eliminate leaks. Minimum height 11 inches with a maximum height of 17-5/8 inches. In-line design for increased ease of use in positioning and operation. Includes free seal kit for extended product life. Chrome piston pump and ram for additional rust resistance.
OTC 4547 Stinger Axle Nut Socket Set – FWD #ad - Contained in a blow-molded plastic storage case. Otc stinger axle nut socket set-fwd features extra long, 1/2″ drive 6-point chrome molybdenum sockets for heavy-duty use in removing and installing axle nuts. Use with a ratchet, breaker bar, or torque wrench.
OTC (1526A) Stinger Two Speed 3-1/2-Ton Service Jack #ad - Extra wide lift range from 4 inch to 21 inch and a long 48 inch spring-loaded handle provides rapid return after each pump. Ideal floor jack for either a large automotive service center or a one-person shop. Rolled edges add strength and resist twisting and pinned 4-3/4 inch saddle will not lift off during use. One pump to load three pumps to full height unloaded.
OTC (5372) Stinger 3 Ton Jack Stands – Pair #ad - A self-locking ratchet handle cannot be released under load. A durable baked enamel finish resists corrosion. The stands also conform to ansi pald load rating standard. These stands are factory tested before shipment, and have welded foot pads that resist sinking into soft ground or asphalt. Made with a formed and welded steel base for strength.
OTC 4652 Stinger Adjustable Fan Clutch Holding Tool #ad - Jaws adjust from 1/ 2 inch to 8-5/16 inch opening. It comes with a long handle that offers leverage for extra torque. The jaws lock in place to securely hold water pump bolts. Otc stinger adjustable fan clutch holding tool adjustable jaws fit various water pump pulley bolt patterns.
OTC (9314) Stinger 12 Ton Short Bottle Jack #ad - In-line design for increased ease of use in positioning and operation. Includes free seal kit for extended product life. Chrome piston pump and ram for additional rust resistance. Minimum height 7-1/16 inches with a maximum height of 13-5/8 inches. Forged base and cylinder to ensure strength and eliminate leaks.
OTC (5373) Stinger 6 Ton Jack Stands – Pair #ad - Made with a formed and welded steel base for strength. A self-locking ratchet handle cannot be released under load. The stands also conform to ansi pald load rating standard. A durable baked enamel finish resists corrosion. These stands are factory tested before shipment, and have welded foot pads that resist sinking into soft ground or asphalt.
OTC 4523 Stinger Offset Hose Clamp Plier #ad - Otc stinger offset hose clamp pliers head is offset from handle to allow access to hard-to reach clamps. Swivel jaws allow pliers to be used on many different flat-band and ring-type hose clamps.
OTC 4496 Stinger Hose Clamp Plier Set – 6 Piece #ad - The set contains straight hose clamp pliers set hose removal tool flat-type hose clamp pliers offset hose clamp pliers and a 45 degree hose clamp pliers. Otc stinger hose clamp pliers set, 6 piece five different styles of hose clamp pliers which will service most flat-band and ring-style hose clamps and a hose removal tool.
OTC 4565 Stinger 2-7/8″ to 3-1/4″ Swivel Handle Oil Filter Wrench #ad - Features a 1 inch wide stainless steel band for positive grip on the filter. Swivel handle oil filter wrench. Fits filters ranging from 2-7/8 inch to 3-3/8 inch in diameter. Swivel handle makes it easy to turn filters in hard-to-reach areas.
OTC 1512 Stinger 20-Ton Service Jack #ad - The counter-balanced spring-assisted handle has a three-position lock. Otc stinger 20-ton service jack low-profile stance and extended height add to versatility. Its wheels and swivel casters feature internal bearings. Either the foot pedal or jack handle may be used for pumping action.
OTC 4503 Stinger Double Flaring Tool Kit #ad - Includes five adapters covering 3/16 inch through 1/2 inch and 48 mm through 127 mm. Chrome swivel is made of alloy steel and reduces friction. Forged yoke is made of heat-treated steel. Designed for double or single flare in copper aluminum soft steel brake line and brass tubing. Housed in a blow-molded storage case.
OTC 4723 Stinger Ear-type CV Boot Clamp Plier #ad - For removal of the front hub assembly necessary for wheel bearing or brake rotor service. Provides the mechanical advantage and straight pull not possible with a slide hammer. 1988-2000 gm 1/2-ton 3/4-ton and 1-ton trucks tahoe suburban and yukon. 1994-2000 dodge 1/2-ton 3/4-ton and 1-ton ram trucks. 1997-2000 ford 1/2-ton trucks and expeditions 1985-2001 jeep cherokee.
OTC 4722 Stinger Heavy-Duty CV Boot Clamp Installer #ad - It ensures even precise crimping and eliminates possibility of damage to the clamp boot or hose. It may also be used to crimp the clamps used on fuel and cooling system hoses. Otc stinger heavy-duty cv boot clamp installer is designed to clamp the ear-type cv boot clamps used on front-wheel drive vehicles.
OTC 4533 Stinger W-Body Strut Tool Kit for GM #ad - Otc stinger w-body strut tool kit for gm includes one t50 torx bit a universal drive handle and a double-ended socket. It works on gm w-body vehicles 1988-96 pontiac grand prix 1988-98 olds cutlass supreme and chevrolet lumina sedan 1995-99 chevrolet monte carlo 1988-96 buick regal. Use one end of the socket to remove/install the jounce bumper the other end to remove/install the strut cap nut.
OTC (1784D) Stinger Jack Stand – Pair #ad - These stands conform to ansi pald load rating standard and are factory tested before shipment. The base is 12-1/8″ x 10-7/8″ with a height range of 17-1/2″ to 27-1/2″. The otc 12-ton jack stands have formed and welded steel base for strength and the durable baked enamel finish resists corrosion. The self-locking ratchet handle cannot be released under load.
OTC 4485 Stinger Spot Weld Cutter Set #ad - Otc stinger spot weld cutter set is used with electric drill or air drill to cut 5/16 inch and 3/8 inch spot welds. Cutter bits have cutting teeth on each end. The kit s consists of 3 each 5/16 inch cutter bits, 3 each 3/8 inch cutter bits, and 4 each centering tips.
OTC (5303) Stinger 3 Ton Hydraulic Service Jack #ad - A flanged upper body edge increases strength to resist twisting. Light, compact design makes it easy and convenient to use. 3 ton capacity with a lifting range of 5-3/4 inches to 18-1/2 inches. Built-in safety overload system prevents use beyond the rated capacity. Rear swivel casters for easy maneuvering and positioning.
OTC (5302) Stinger 2-1/4 Ton Hydraulic Service Jack #ad - 2-1/4 ton capacity with a lifting range of 5 inches to 18 inches. Light, compact design makes it easy and convenient to use. Built-in safety overload system prevents use beyond the rated capacity. A flanged upper body edge increases strength to resist twisting. Rear swivel casters for easy maneuvering and positioning.
OTC 4475 Stinger Grooved Pulley Strap Wrench #ad - It holds tighter than a standard strap wrench. Also may be used to rotate the camshaft or crankshaft for engine service. Otc stinger grooved pulley strap wrench is used to hold a grooved pulley when servicing alternators water pumps power steering pumps etc.
OTC 4720 Stinger CV Boot Clamp Plier for Chrysler #ad - Boots found on various chrysler plymouth and dodge front-wheel drive vehicles. N. C. I. It works on a. Otc stinger cv boot clamp pliers for chrysler required tool for correct installation of strap-and-buckle style cv boot clamps. K. And g. It prevents damage to cv boot and clamp during installation.
OTC 4512 Stinger Internal And External 8 Piece Snap-Ring Pliers Set #ad - The kit includes a 4512-1 090 inch tip straight pliers, 4512-2 090 inch tip 90 degree pliers, 4512-3 070 inch tip straight pliers, 4512-4 070 inch tip 90degree pliers, 4512-5 047 inch tip straight pliers, 4512-6 047 inch tip 90degree pliers, 4512-7 038 inch tip straight pliers, 4512-8 038 inch tip 90degree pliers, 4512-9 straight tip pick and a 4512-10 90degree tip pick all contained in a blow-molded plastic storage case. The otc stinger internal and external snap-ring pliers kit is made of heavy-gauge tempered steel for long life and durability.
OTC 4504 Stinger ISO Bubble Flaring Tool Kit #ad - Designed for crack-free bubble flares on soft steel tubing used in automotive brake systems. Includes four dies 475 6 8 and 10 mm. Flaring bar and all the adapters needed for iso bubble flaring. Housed in a blow-molded storage case. Forged yoke is made of heat-treated steel.
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.